Lee
FEATURES
-For .270 Winchester
-Case Length Gauge
-Precise, easy way to trim to length & square the case mouth
-Used with the Cutter & Lock Stud or Zip Trim
FEATURES:
-Includes full length sizing die, easy adjust dead length bullet seating die, factory crimp die, universal shell
holder, powder dipper, & instructions/load data
Other Features: X-press shell holder for app automatic processing press.Allows the case to pass through the shell holder after operations are performed.Fits wsm's, 7mm rem mag, and 303 british
Other Features: Replaces the small and large case sliders found on pro 1000 and loadmaster presses.
FEATURES
-.500 S&W
-Incorporates a collet to apply a rifle type crimp to the case
-Makes these very difficult to crimp cartridges a delight to reload
-Bullets do not need a crimp groove, as the collet is so powerful it will form one
Note: This die is not carbine.
FEATURES
-3 die storage box for rifle and pistol reloading dies
FEATURES
-Largest opening and longest stroke handle is adjustable to provide the least travel
-Rigid cast iron construction
-Adjustable handle
-Automatic primer arm
-Works with large series 1 1/4-12 dies
-Includes threaded adapter to accept standard 7/8-14 dies
-Large 1 1/8 diameter ram
-Accepts standard shell holders
FEATURES
-For 6.5 Carcano
-Case Length Gauge
-Precise, easy way to trim to length & square the case mouth
-Used with the Cutter & Lock Stud or Zip Trim
FEATURES
-Factory crimp die for .338 Winchester Magnum
-Crimps bullet in place more firmly than any other tool
-A firm crimp improves accuracy
-Higher start pressure insures a more uniform pressure curve & less velocity variation
FEATURES
-#12L quick change shell plate
-For Load-Master Press
-For 7.62x39, 6mm PPC, .22 PPC & similar
FEATURES
-For .30-30 Winchester
-Full length sizer die
-Easy adjust dead length bullet seating die (no crimp)
FEATURES
-For .329
-Lubricates & sizes cast bullets
-Seats & crimps gas checks
-Fits any standard 7/8x14 thread reloading press
**DOES NOT INCLUDE LUBE**
Other Features: **lube not included**
FEATURES
-Factory crimp die for .45-70 Government
-Crimps bullet in place more firmly than any other tool
-A firm crimp improves accuracy
-Higher start pressure insures a more uniform pressure curve & less velocity variation
FEATURES
-Full length 2 die set for .22 TCM
-Full length sizing die
-Bullet seating die
-Universal shell holder
-Powder dipper
-Instructions/load data
FEATURES:
-Caliber: 50 BMG
-Factory Crimp
-Threads: 1-1/4" - 12
FEATURES
-#1S quick change shell plate
-For Load-Master Press
-For .38 Special, .357 Magnum & similar
FEATURES
-Pacesetter 3 die set for .204 Ruger
-Full length sizing die
-Bullet seating die
-Factory crimp die
-Universal shell holder
-Powder dipper
-Instructions/load data
FEATURES
-Complete reloading system for.270 Winchester
-Does not include rubber mallet
FEATURES
-Used for .45caliber bullets with lengths from .5"up to .67"long
-Converts the Bullet Feed Kit to another caliber or length of bullet
FEATURES
-.300 Winchester Magnum
-Collet die only
-Sizes just the neck
-Needs no lubrication
FEATURES
-Full length 2 die set for .25-35 Winchester
-Full length sizing die
-Bullet seating die
-Universal shell holder
-Powder dipper
-Instructions/load data
FEATURES
-.309diameter
-170 grain
-Round nose bullet
-Suitable for cartridges like .30 caliber rifle
-Handles included
FEATURES
-Undersize sizing die
-For .45 ACP
FEATURES
-Factory crimp die for .30-06 Springfield
-Crimps bullet in place more firmly than any other tool
-A firm crimp improves accuracy
-Higher start pressure insures a more uniform pressure curve & less velocity variation
FEATURES
-For .38Smith & Wesson Pistol
-3-die set
-Carbide full length sizing die
-Bullet seating die
-Powder thru expanding die
-Universal shell holder
-Powder dipper
-Instructions/load data
FEATURES
-For .38 Super, .38 ACP
-Sizes the cartridge while being crimped
-Every round will positively chamber freely
-Applies a roll crimp
-Adjusting screw quickly & easily sets desired amount of crimp
Other Features: X-press shell holder for app automatic processing press.Allows the case to pass through the shell holder after operations are performed.Fits 7.62x54r, and 500 s&w
FEATURES
-For .35 Whelen
-Case Length Gauge
-Precise, easy way to trim to length & square the case mouth
-Used with the Cutter & Lock Stud or Zip Trim
FEATURES
-R-14 universal shell holder
-For .44/40, .45 Long Colt& similar
FEATURES
-Double Cavity Mold
-Produces a .451 diameter ball
-137.71 grains
-Includes handles
FEATURES
-.357 Magnum
-Incorporates a collet to apply a rifle type crimp to the case
-Makes these very difficult to crimp cartridges a delight to reload
-Bullets do not need a crimp groove, as the collet is so powerful it will form one
Note: This die is not carbine.
FEATURES
-Six cavity mold
-Produces a .358 diameter
-158 grainflat nose bullet
-Suitable for cartridges like 38 Special, 38 S&W, 38 Colt New Police, 375 Mag.
-Bullet overall length: .630"
-Distance from crimp groove to nose of bullet: .27"